User contributions
- 23:53, 10 March 2017 (diff | hist) . . (0) . . m EmonTx Arduino Shield (→Overview)
- 23:52, 10 March 2017 (diff | hist) . . (-71) . . m EmonTx Arduino Shield
- 21:35, 25 December 2016 (diff | hist) . . (+95) . . EmonTx V3.4 (→Temperature Monitoring)
- 21:31, 25 December 2016 (diff | hist) . . (+103) . . EmonTx V3.4 (→RJ45 Connection)
- 15:08, 11 September 2016 (diff | hist) . . (+137) . . m MQTT WiFi Relay (Single channel board: Link to Github added) (current)
- 15:02, 11 September 2016 (diff | hist) . . (+495) . . MQTT WiFi Relay (Wiring diagram for Single Relay board added. CONFIRMATION IS REQUIRED THAT ALL OTHER DETAILS ARE THE SAME AS THE 3-CHANNEL VERSION)
- 16:41, 21 July 2016 (diff | hist) . . (+37) . . EmonTx Arduino Shield (Pin use table added)
- 16:38, 21 July 2016 (diff | hist) . . (+14) . . N File:Pin use.png (SMT2.5 Pin use) (current)
- 20:02, 22 July 2015 (diff | hist) . . (+419) . . EmonTx V3.4 (Serial Connection: Tx and Rx pins of the FTDI connector on both PCB and schematic are reversed. Note added to and to "Direct connection emonTx V3 > Raspberry Pi GPIO".)
- 22:28, 27 May 2015 (diff | hist) . . (+266) . . EmonTx V3 (Firmware - Calibration: Expanded to make clear that the standard calibration assumes nominal component values, and can usually be improved.)
- 22:23, 27 May 2015 (diff | hist) . . (+265) . . EmonTx V3.4 (Firmware - Calibration: Expanded to make clear that the standard calibration assumes nominal component values, and can usually be improved.)
- 20:54, 21 April 2015 (diff | hist) . . (-160) . . m EmonTx V3 (Reverted edits by RWall (talk) to last revision by Glyn)
- 20:52, 21 April 2015 (diff | hist) . . (+160) . . m EmonTx V3 (Link to PCB Layout & Schematic on GitHub added.)
- 20:47, 21 April 2015 (diff | hist) . . (+159) . . m EmonTx V3.4 (Link to PCB layout & schematic on GitHub added.)
- 11:56, 12 March 2015 (diff | hist) . . (+1) . . m EmonTx V3 (→Features)
- 17:39, 25 February 2015 (diff | hist) . . (+220) . . EmonTx V3 (→Arduino Firmware Info)
- 14:52, 25 February 2015 (diff | hist) . . (+1) . . EmonTx V3.4 (→Arduino Firmware Info: Added note about no default sketch loaded if supplied without a radio.)
- 14:48, 25 February 2015 (diff | hist) . . (+223) . . EmonTx V3.4 (→Arduino Firmware Info)
- 17:17, 19 February 2015 (diff | hist) . . (+95) . . EmonTx Arduino Shield (→Hardware Setup Instructions)
- 22:39, 1 February 2015 (diff | hist) . . (+15) . . EmonTx V3 (→Temperature Monitoring: In the text, Dig19 and Dig5 were transposed. The table is correct to the schematic & PCB s/s.)
- 18:55, 1 February 2015 (diff | hist) . . (+22) . . EmonTx V3.4 (→Temperature Monitoring: In the text, Dig19 and Dig5 were transposed. The table is correct to the schematic & PCB s/s.)
- 22:53, 15 December 2014 (diff | hist) . . (+285) . . EmonTx V3.4 (Vrms (not Irms) is calculated with AC adapter present. Line about default sketch is 1-phase added. Multiple minor typos corrected.)
- 14:37, 15 December 2014 (diff | hist) . . (+849) . . EmonTx V3 (→Accuracy)
- 14:17, 15 December 2014 (diff | hist) . . (+1,435) . . EmonTx V3 (→Three-Phase)
- 13:58, 15 December 2014 (diff | hist) . . (+798) . . EmonTx V3 (→Single Phase)
- 23:32, 12 December 2014 (diff | hist) . . (+234) . . m EmonTx V3 (Link to Schematic and PCB layout files added)
- 00:42, 9 December 2014 (diff | hist) . . (+200) . . ADE7878A rpi (Warning added)
- 11:56, 29 August 2014 (diff | hist) . . (+795) . . EmonTx Arduino Shield (Note re compatibility problem with Arduino clones with Ethernet/Ethernet Shield)