- 1 emonTx V3.4
- 1.1 Features
- 1.2 Port Map
- 1.3 Overview
- 1.4 DIP Switch Config
- 1.5 Power Supply Options
- 1.6 Uploading Arduino Firmware
- 1.7 Standard Operation
- 1.8 Extended Operation
- 1.9 Connectivity
- 1.10 Electrical Characteristics - Absolute min / max
- 1.11 Enclosure =
The emonTx V3.4 is the latest version of the emonTx Low Power Wireless Energy Monitoring Node designed for monitoring AC electrical power on a maximum of 4 separate (household/building) circuits using non-invasive clip-on CT sensors and an AC-AC Voltage adapter to provide a voltage signal for Real Power calculations. The emonTx V3.4 is a minor update to the emonTx_V3
New features on emonTx V3.4 over V3 shown in bold
- Measure AC Apparent Power, AC Real power* and AC RMS voltage*
- 3 x single-phase CT current sensor inputs (100A / 24KW @ 240V max)
- 1 x high sensitivity single-phase CT current sensor input channel (18.8A / 4.5KW @ 240V max)
- 1 x RJ45 input for connecting DS18B20 temperature sensors
- Single AC-AC adapter can power the unit and provide AC voltage measurement
- An on-board 3x AA battery option with remote monitoring of battery voltage
- Terminal block access to power rails, digital and analogue I/O and IRQ port for connecting pulse counting sensor / DS18B20 temperature / Aux sensors
- DIP switch selection of RF node ID and 240V/120V AC adapter selection, see #DIP Switch Config
* when AC-AC voltage adapter is connected
A schematic diagram and PCB layout (Eagle CAD format) can be found on GitHub.
Note: The FTDI connector Tx and Rx pins are reversed on the PCB legend and on the Schematic. Data is received by the emonTx on the Tx pin and transmitted by the emonTx on the Rx pin.
Using an ATmega328 microprocessor, the emonTx V3.4 runs standard Arduino sketches. It is easy to customise and upload code using the Arduino IDE and a USB to UART cable.
The data from the emonTx V3.4 is transmitted via an RFM12B / RFM68CW 433/868 MHz radio to an emonBase web-connected base-station (we recommend a Raspberry Pi with an RFM12Pi) which then posts the data onto an emoncms server (e.g. http://emoncms.org) for logging, processing and graphing.
DIP Switch Config
The emonTx V3.4 has two DIP switches enabling selection of node ID and setting UK/EU or US AC-AC adapter choice without having to change the firmware. The unit must be restarted after changing DIP switch positions. Default DIP switch selection (both off) is node ID 10 and 240V AC.
Note: newer emonTx V3 firmware (V2.3+) use node ID 8 and 7, instead of 10 and 9 (shown below) see emonhub config guide for more info
Power Supply Options
There are four ways to power the emonTx V3:
- USB to UART cable - only recommended for short periods while programming, it is recommended to remove all other power sources
- 5V DC Mini-USB cable - remove jumper JP2 when powering via DC if AC adapter is present
- 3 x AA Batteries - remove jumper JP2 when powering via DC if AC adapter is present
- 9V AC-AC power adapter - with jumper JP2 closed (If jumper 2 is left open then the AC-AC adapter will be used for power sampling but not to power the emonTx V3 - see Powering via AC below)
Powering via DC (1-3)
When powering the emonTx V3 via DC (1-3) (and running the main emonTx firmware (emonTxV3_RFM12B_DiscreteSampling)) the emonTx V3 will take Apparent Power measurements, measuring only current, assuming the Power Factor of 1 and Vrms to be 230V, power saving mode will also be implemented, going into sleep mode between readings (default every 10s) to save battery power.
The red LED indicator will illuminate for a couple of seconds then extinguish never to flash again if powering from a DC source. If the LED flashes multiple times at startup this indicates the emonTx is detecting an AC waveform - this can happen if an AC adapter has just been removed, hit the reset button if this occurs. When powering the unit via 5V USB/battery it is advisable to remove the JP2 jumper if an AC-AC adapter is present.
Powering via AC (4)
A nice feature of the emonTx V3 is the ability to use an AC-AC adapter to power the unit while simultaneously providing an AC voltage sample. If the emonTx V3 detects the presence of an AC adapter at startup, it will automatically implement Real Power and Vrms measurements by sampling the AC voltage. Real Power is what you get billed for, and depending on the appliances connected to the circuit being monitored, can vary significantly from Apparent Power - see Building Blocks for more info on AC power theory. For best energy monitoring accuracy, we recommend powering the EmonTX with an AC-AC adapter whenever possible.
Using the AC voltage for reference also enables the emonTx to monitor the direction of current flow. This is important for solar PV monitoring. If you notice a negative reading when you were expecting a positive one, reverse the orientation of the CT on the conductor. The red indicator LED will flash at startup then flash once every 10 seconds to indicate an AC waveform has been detected. Sleep mode will be disabled to keep a more consistent power draw on the AC circuit.
Important note regarding powering with AC: powering via AC is recommended only for standard emonTx operation without auxiliary sensors (apart from a maximum of 4 DS18B20 temperature sensors) or equipment (e.g. relay modules) connected. Correct operation via the AC supply is critically dependent upon using the correct AC-AC adapter. If you are using the recommended AC-AC adapter and the current draw exceeds 10 mA and the mains supply is below the minimum allowable, then circuit operation will be impaired, adversely affecting the accuracy of the emonTx. To avoid damage to the emonTx V3 circuits, the current drawn from the AC circuit should never exceed 60mA - see the technical wiki for more info. If more than 10 mA of current is required, it is recommended to remove jumper 2 (JP2) and power the emonTx via the 5V mini-USB connector. When JP2 is removed, the AC-AC adapter (if connected) will be used only to provide an AC voltage sample, i.e. it will not power the emonTx.
Uploading Arduino Firmware
Compiling and Uploading using Arduino IDE
The emonTx V3 uses the ATmega328 microcontroller (same as Arduino Uno) and comes with the Optiboot (Arduino Uno) serial bootloader installed. This makes it super easy to upload new code to the emonTx V3 from the Arduino IDE.
A USB to UART cable is required to upload new Arduino firmware sketches
Start by downloading the firmware, libraries and setting up the Arduino programming environment by following this guide:
Once complete the emonTx V3 firmware location should be navigable from within the Arduino IDE by going to:
File > Sketchbook > OpenEnergyMonitor > emonTxFirmware > emonTxV3
Flashing Pre-compiled .hex
The main emonTx v3.4 RFM69CW  firmware as pre-loaded onto pre-build emonTx, is also supplied as a pre-compiled .hex file.
GitHub can be used to obtain the latest version:
Linux : use AVRdude
$ sudo apt-get install avrdude
$ avrdude -v -c arduino -p ATMEGA328P -P /dev/ttyUSB0 -b 115200 -U flash:w:emonTxV3_RFM69CW_DiscreteSampling_433.cpp.hexx
Specify the port your USB to UART programmer is connected to, and the path name of the .hex file
Windows :you might be able to use the the XLoader application to upload .hex files (we have not tested this, please update the wiki if you have)
Flashing the Bootloader
Not normally required
The OptioBoot Arduino Uno serial bootloader should be ready loaded onto the ATmega328 on the emonTx from the factory. If however, for any reason you need to reload the bootloader and set the fuses, here is the procedure:
The stock emonTx firmware including the bootloader, can be downloaded in pre-compiled .hex form from github. Look for a .hex file including the word "bootloader" in the title, on the emonTx V3 GitHub page.
The .hex file can be flashed, and the fuses set, on the ATmega328 using the following avrdude command:
$ sudo avrdude -v -p atmega328p -c avrispmkII -P usb -e -Ulock:w:0x3F:m -Uefuse:w:0x05:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m -U flash:w:emonTxV3_4_RFM12B_DiscreteSampling_bootloader.cpp.hex:i -Ulock:w:0x0F:m
or, to speed things up:
$ sudo avrdude -V -u -p atmega328p -c avrispmkII -P usb -e -Ulock:w:0x3F:m -Uefuse:w:0x05:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m -U flash:w:emonTxV3_4_RFM12B_DiscreteSampling_bootloader.cpp.hex:i -Ulock:w:0x0F:m
If, for any reason e.g to make a backup, you want to read the data from the ATmega328 this can be done with:
$ avrdude -v -p atmega328p -c avrispmkII -P usb -U flash:r:test_intel.hex:i
Arduino Firmware Info
See the GitHub readme for firmware info:
All emonTx V3 firmware is available on Github:emonTxFirmware
All emonTx V3s sold pre-assembled with a radio module are shipped with Discrete Sampling firmware. This is the main firmware for the emonTx V3 and has been tested and calibrated based on nominal component values. If better accuracy is required, and facilities are available, the unit should be re-calibrated to take account of variations present in the components used. You will need access to a programmer to reload the sketch. If you ordered an emonTx V3 without a radio module, no firmware will be loaded, although there will be a bootloader present. You will need access to a programmer to load a sketch.
The Discrete Sampling firmware has the following features:
- Detection of AC-AC adapter sets Apparent Power / Real Power Sampling accordingly
- Detection of battery / USB 5V or AC-DC power method and sets sleep mode accordingly
- Detection of CT sensors. Samples only from connected channels
- Detection of remote DS18B20 temperature sensor
This firmware is suitable for real power measurements in a single-phase installation only. If you have a three-phase installation and need to measure real power, you will need to replace the sketch with the equivalent three-phase firmware.
Note: Detection of the connected senors use takes place at power-on. The sketch must be re-started (press the reset button) if any sensors are connected or disconnected after power-on.
The emonTxV3_RFM12B_Discrete Sampling firmware samples 10 full AC cycles, i.e. 200 ms per measurement from each CT at a rate of approximately 2500 samples per second. It is assumed the power does not fluctuate significantly during the time the microcontroller is asleep, which is usually good enough for typical household monitoring. If greater precision is required (as is the case with PV energy Diversion it is recommended that you use a PLL or continuous sampling sketch. See the RFM12B firmware examples folder on GitHub.
CT Energy Monitoring
A DS18B20 digital temperature sensor can easily be connected to the emonTx V3 by connecting the sensor to the emonTx V3 screw terminal block or RJ45 connector. The default firmware (discrete sampling) supports auto-detecting one DS18B20 sensor. Multiple DS18B20s can be daisy-chained, but this will require changes to the pre-installed emonTx firmware - you may also run into power draw issues depending on how you are powering the emonTx (see Power Supply Options above).
In order to save power when running on batteries, the emonTx V3 supports switching off of the DS18B20 in-between readings and performing the temperature conversion while the ATmega328 is sleeping. To do this, power (3.3 V) is supplied to the DS18B20's power pin from Dig19 (ADC5), this digital pin is switched off between readings. (This facility is available only if the temperature sensors are connected via the terminal block.) The data connection from the DS18B20 is connected to Dig5, this I/O pin has a 4K7 pull-up resistor to 3.3 V on-board the emonTx V3's PCB, as required by the DS18B20.
A DS18B20 sensor can be connected directly to the RJ45 socket, or an RJ45 to terminal block breakout can be used to connect multiple sensors:
Note: The RJ45 socket does not support power supply switching via Dig19 (ADC5) as described above.
Additional RJ45 breakouts are available from Sheep Walk Electronics
The emonTx V3.4 uses a standard RJ45 DS18B20 pin-out as used by Sheepwalk Electronics and others:
Terminal Block Connection
To connect an external DS18B20 to the emonTx V3 screw terminal block connections are as follows
|Screw terminal pin||DS18B20 Connection|
|3 - GND||GND (Black)|
|5 - Dig19||Power (Red)|
|6 - Dig5||Data (White)|
Utility Meter Interface
Optical Pulse Counting
The OpenEnergyMonitor optical pulse sensor can be connected directly to the emonTx V3 via its RJ45. As of March 2015, pulse counting has been integrated into the main emonTx V3 firmware and shipped as standard (Firmware V1.7+)
Many meters have pulse outputs, including electricity meters (single phase, 3-phase, import and export), gas meters, water flow meters etc. The pulse output may be a flashing LED or a relay (usually solid state) or both. We recommend using the optical interface where available, as this decouples the monitoring equipment from any high/mains voltages.
In the case of an electricity meter, a pulse output corresponds to a certain amount of energy passing through the meter (kWh/Wh). For single-phase domestic electricity meters e.g. Elster A100c, each pulse typically corresponds to 1 Wh (1000 pulses per kWh). Water and gas meters will usually be marked to show the quantity of water (litres/gallons) or of gas (cubic meters/cubic feet) that each pulse represents.
The emonTx V3.4 has one spare interrupt input (IRQ 1, Dig3) which can be used for pulse counting. This is broken out on terminal block port 4 and RJ45 socket
Pules are counted, and the current pulse count transmitted via RF, as the final variable in the JeeLib packet structure. The emonCMS wh_accumulator input process can be used to log the pulse count. The wh_accumulator input process detects when the pulse count gets reset to zero (after the emonTx is reset) and continues to accumulate ignoring the reset. An scaler input process can be used to convert number of pulses to Kwh. For example: my utility meter outputs 800 pulses per Kwh so each pulse is 0.8wh. I can multiple the number of pulses by 0.8 to get number of wh elapsed or by 0.0008 for number of Kwh elapsed.
Read more about pulse counting OpenEnergyMonitor pulse sensor documentation page.
emonTx V3 Hardware Connections
You should connect the pulse input into emonTx V3.4 terminal block port 4 (IRQ 1 / Digital 3) or RJ45 socket pin 6, see below for pin-out. If you are connecting a hard-wired pulse output you may need to add a pull-down resistor. If you are using an optical counter (e.g TSL257) you should connecting the power pin to the 3.3V or 5V (if running off 5V USB)
|Screw terminal pin||Connection|
|1||5V (if powered via 5V USB)|
|4||IRQ 1 / Dig3|
We recommend powering the emonTx v3 from either a 5V USB or AC-AC adapter when used for pulse counting operation. Due to the additional power requirements of the optical pulse sensor, battery life will be significantly reduced compared to running an emonTx from 3 x AA batteries for CT operation only.
Direct Optical Interface
if you have an Elster meter (tested with Elster 100C) the emonTx V3 with an IR TSL261R sensor can be used to interface directly with the meter protocol to read off the exact accumulated watt hours that you have generated or used. This reading can be used on its own or to cross-check and calibrate CT based measurement. See here for original blog post
The emonTx communicates data back to a web-connected base station (Raspberry Pi with RFM12Pi / RFM69Pi) via low power 433MHz / 868 MHz RF
See RFM12B Building Block documentation:
Using latest JeeLib library the RFM69CW is backward compatible with RFM12B
To enable RFM69CW ensure
define RF69_COMPAT 1
is set to '1' at the begging of the sketch. Or use a pre-compiled .hex with RFM69CW in the title, see emontx V3.4 GitHub repo
See photo below showing RFM69CW module orientation when soldered onto emonTx V3.4:
Whilst the system was designed to transfer data via radio it is possible to link the emonTx and Raspberry Pi by wires. It should be noted that this is NOT the standard setup.
Direct connection emonTx V3 > Raspberry Pi GPIO
Both the Raspberry Pi and emonTx V3 run at 3.3V so the serial RX and TX lines can be directly connected. the 5V power rail from the Raspberry Pi can be supplied to the emonTx which is then stepped down to to 3.3V through the emonTx V3's voltage regulator. 5V is provided by the red wire (see photo). The ground connection is the black wire and the serial data going from the emonTx to the Raspberry Pi is the green wire. Wire for serial data going the other (Pi to emonTx) has not been connected in this example but could be added if two way comms is required.
Note that on the PCB and on the Schematic, the Tx and Rx pins are labelled according to the connections on the Programmer, meaning that data is received by the emonTx on the Tx pin and transmitted by the emonTx on the Rx pin.
Electrical Characteristics - Absolute min / max
Max / typical
if exceeded damage might happen
|CT 1-3||Monitoring Power @ 240V||23kW / 95.8A||60kW / 250A||Using 22R burden and YHDC SCT-013-00 with 22 turns|
|CT 4||Monitoring Power @ 240V||4.5kW / 19.2A||4.6kW max measure – 19.7kW / 82A Max dissipation||Using 120R burden and YHDC SCT-013-00 with 22 turns|
|AC-DC half-wave supply||Current output||20mA||60mA||Current draw above 20mA AC sample signal will be effected|
|3.3V Rail current output||When powering with 5V USB||150mA||168mA||Limitation SOT22 MCP1700 Ta=40C Vi=5.25V|
|Storage Temperature||Not programmed||-50C||+150C|
|5V Input Voltage||USB/FTDI/5V Aux||+3.4V||+6V||+6.5V (see note 1)||See note 1|
|3.3V Supply Voltage||on 3.3V supply rail||2.6V *||3.3V||3.9V RFM69CW||*ADC readings will be incorrect if Vcc!=3.3V|
- The emonTx V3 PCB is 100mm x 80mm and enclosed in an EBS80 enclosure by Lincoln Binns, see data sheet
- Community contributed DIN-RAIL mount fixing on Thingiverse