Raspberry Pi

From Wiki | OpenEnergyMonitor
Revision as of 17:31, 14 March 2017 by Bill thomson (talk | contribs) (→‎Troubleshooting)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Raspberry Pi

With the addition of an #RFM12Pi expansion board, a Raspberry Pi running emoncms can be used as a powerful emonBase base-station to log, process and visualise energy, temperature and other environmental data.

Data can be logged locally to the Raspberry Pi's SD card and/or to a remote emoncms server. Emoncms graphs and dashboards can be served from the Raspberry Pi's web-server.

RFM12Pi installed Raspberry Pi


The RFM12Pi GPIO expansion board enables the Raspberry Pi to receive or transmit data via RFM12B wireless (433/868/915MHz) from other OpenEnergyMonitor modules such an an emonTx energy and temperature monitoring node, or an emonGLCD display. The RFM12Pi expansion board can be purchased from the OpenEnergyMonitor shop

RFM12Pi Front

For the new pre-assembled RFM12Pi V2 see new documentation

Technical Overview

The RFM12Pi is uses an ATtiny84 microcontroller running a modified version of JeeLabs RF12Demo to receive wireless data via an RFM12B wireless transceiver and transmit data via the Pi's internal serial port

The RFM12Pi board and much of the software is the work of Martin Harizanov. We worked with Martin on the hardware design and emoncms software integration. We owe Martin a big thank you for the effort put into making this solution work well.

Design Files & Part List

Quantity Part
1x ATtiny84 (RF12B firmware preloaded)
2x 100nF
1x 5mm LED
2x 10K (brown, black, orange, gold)
1 x 100R (brown, black, brown, gold)
1x RFM12B (433/868 Mhz)
1x GPIO 6x2 pin header female socket
1x ISP 3x2 pin header

The RFM12Pi's Eagle CAD PCB design files, schematic and Arduino based firmware can be downloaded from Martin Harizanov's GitHub

1) RFM12Pi Assembly

It's recommended you read this guide and familiarise yourself with the steps before you start the build.

Step 1 - Identify Components and Kit Contents

Lay out, and identify, the components from the kit.


Ok, we're ready to start. Here is the PCB:


Step 2 - 10k Resistors

As a general principle we're going to build up from the lowest-profile component. Start with the resistors. Bend each leg of the resistor 90 degrees, right next to the body. The last colour on all of the resistors is brown - it's recommended that you align them all in the same direction and have the brown at the same end. The colours for the 10K resistor are (brown, black, orange, gold).


Step 3 - 100R Resistor

Add the 100R resistor in exactly the same way, its colours are (brown, black, brown, gold)


Step 4 - ATtiny84 DIL Socket

Fit the ATtiny84 DIL Socket as shown in the picture. Note that one end has a small notch in it - this signifies pin 1 and should match up with the notch on the PCB silkscreen. Make sure the socket is fitted flat on the board.


Step 5 - Green LED

Add the green LED. Ensure the long leg (and round edge) are facing the + symbol printed on the board.


Step 6 - RFM12B RF

Place the RFM12BRF module on the pads (observe the orientation - Crystal on the LEFT) and solder each pad to the board.


Step 7 - 100nF Ceramic Capacitors

Add the two 100nF ceramic capacitors one at either end of the board.


Step 8 - 3x2 pin ISP header

Add the 3x2 pin ISP header. Long pins point up, short pins are soldered to the board.


Step 9 - 6x2 pin GPIO header female socket

The GPIO socket needs to go on the bottom of the board.


Step 10 - RF Antenna

Add the Antenna through the bottom-right hole, and solder it in place. The length of the Antenna is dependant on the frequency of your RFM12B module. This is a piece of wire 82mm long for 868MHz and 165mm for 433MHz which will act as a quarter-wave antenna. For more information on the RFM12B see: [1]


Step 11 - ATtiny84 Integrated Circuit

Fit the ATtiny84 IC into its socket. Note the spot next to pin 1 and ensure you insert it the right way round.

ICs usually come with their legs pointing slightly outwards. To get them to fit easily into the socket, put the legs flat on a desk and rock the IC slightly to bend the pins inwards - do that to both sides and try to fit it into the socket again.


Step 12 - Relax job done

Turn off your soldering iron and go and have a cup of tea :-)

2) Prepare SD Card

There are two options to set up your Pi with emoncms and RFM12Pi. You can set up the system from scratch, or you can quickstart it by downloading the ready-to-go SD card image.

Using ready-to-go image Recommended

Build from scratch

(Optional) Bootload the ATtiny84

The ATtiny84 microcontroller should come pre-loaded with the required firmware (RFM12 Demo sketch). If you bought the RFM12pi from the OpenEnergyMonitor Shop jump ahead to #RaspberryPi Setup. However, if you have obtained a blank ATtiny84 you'll need to upload the rf12 demo firmware to it:

The 'easy' way to do this is to flash the pre compiled hex file onto the ATtiny, this avoids the need to set up the Arduino IDE for an ATtiny, getting the correct Arduino libraries, etc:

  1. Download the pre compiled RF12 demo .hex file from the firmware folder on Mharizanov's RF12Pi Github Repo
  2. Power the RF12Pi board with 3.3V, this can be done from the Pi
  3. If you have an AVR ISP MKII programmer simply connect it to the ISP header and run the following terminal commend:
    • $ sudo avrdude -c avrispmkII -p t84 -P usb -e -Uefuse:w:0xFF:m -Uhfuse:w:0xD7:m -Ulfuse:w:0xE2:m -U flash:w:ATtiny84_RF12_Demo.cpp.hex
    • This avrdude command sets the ATtiny fuses for internal 8Mhz crystal with the BOD disabled and flashes a pre-compiled RF12 Demo sketch

Alternatively you can compile the RF12 Demo sketch yourself using Arduino IDE:

  1. Setup Arduino 1.x IDE for operation with an ATtiny by following our guide
  2. Download a modified version (to use software serial on the ATtiny) of JeeLabs RF12 Demo from Mharizanov's RF12Pi Github Repo
  3. Ensure you have the latest JeeLabs JeeLib Arduino library installed
  4. Power the RF12Pi board with 3.3V, this can be done from the Pi
  5. Connect your AVR programmer to the RF12Pi's ISP header and select your programmer in the Arduino IDE tools>Programmer menu
  6. In the Arduino IDE, select ATtiny84 @ 8Mhz (internal oscillator; BOD disabled) in the Tools>Board menu and click Tools>Burn Bootloader
  7. You are now ready to upload the RF12 Demo to the ATtiny84 using the Arduino IDE
  8. Note: if you're having trouble it might be best to go back to basics with the ATtiny on a breadboard and follow this detailed guide to working with an ATtiny.

SD Card Speed & Benchmarking

We have found that emoncms works better on some brands of cards than others, even if the cards have identical class markings. This section is for listing the make, model, capacity and actual speed of your SD card. The speed can be measured using sudo hdparm -t /dev/sdb assuming your SD card is on sdb.

  • Kingston 4GB Class 4: 50 MB in 3.09 seconds = 16.20 MB/sec - emoncms is slow
  • SanDisk 4GB Class 4: 50 MB in 3.02 seconds = 16.55 MB/sec - emoncms works well
  • SanDisk 8GB Class 10: 54 MB in 3.04 seconds = 17.74 MB/sec
  • Samsung SDHC Essential 32GO Class 10: 70 MB in 3.02 seconds = 23.21 MB/sec - emoncms looks fine

Using WiFi on a Raspberry Pi

Update: The Edimax EW-7811 UN has adapter been reported to work well on the Pi. See OEM forum thread and setup instructions

If you can't get your Pi close to an Ethernet connection, it's possible to use WiFi with a USB WiFi adapter. Setup is quite easy, as the drivers are built into Raspbian on which the pre-built emoncms SD card image is based. I used a USB WiFi adapter based on the RTL8188CUS chipset. Performance was fine, but noticeably slower than Ethernet.

Plug the adapter into the Pi and run $ lsusb and $ lsmod to verify the adapter and the driver 9182cu are listed. As a final check, run $ iwconfig to see if the adapter driver is loaded.

To set up your WiFi connection, edit the config file by running $ sudo nano /etc/network/interfaces and checking that the following is in the file:

auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf  

close and save, then run sudo nano /etc/wpa_supplicant/wpa_supplicant.conf and edit the file by entering your SSID and WPA key in the correct locations

pairwise=CCMP TKIP

Save, close and finally run $ sudo ifup wlan0 to reboot the module and connect to the network. WiFi should now be up and running. You can double check by running $ iwconfig.

If you find the WiFi drops off, you might want to use this script to periodically check for a connection and re-connect.

The script needs to be added to the crontab to run periodically, $ crontab -e to edit or add a new cron tab or '-l' (lower case L) to list existing (if any) crontabs.


If you have followed these instructions and your WiFi still doesn't work, don't worry, you won't be alone! Try reading through the instructions again. The main cause of errors are typos and missed steps. Use Copy and Paste to enter the command lines into the RaspberryPi terminal window. If you're still having problems, ask a question on our friendly forum.

When posting on the forum, please include as much information as you can about what you have done, and what you see. Please include information about your monitoring setup.